dm-24 관련 도와주세요 ㅜㅜ
페이지 정보
본문
dm-24 파이어와이어를 쓰려고 콘솔업데이트 하는 중에 오류가 나더니
부팅이 안 되네요 ㅜㅜ
미국에서 사온거라 극동음향에서는 수리도 안 된다고 하고 ㅜㅜ
너무 오래된 모델이라 그렇지만 도와주세요 ㅠㅠ
관련자료
bravo님의 댓글
아마 절대 안해줄겁니다.
보통 파이어와이어 때문에 업데이트하다가 오류가 잘 납니다.
미디 신호를 받는 과정에서 생기는 오류라고 하던데.
일단 초기화하고 리부팅해보세요.
혹시나 해보셨는지도 모르지만 메뉴얼 내용 첨부합니다.
INITIALIZATION PROCESS
1. With the power OFF hold down the 2nd F button (far left of the
board), the HIGH button (just above in the EQ section) and the -
button (just to the right in the LIBRARY section) while you turn the
power ON.
2. The DM-24 will boot to DIAGNOSTIC MODE. As soon as you see
DIAGNOSTIC MODE on the display you may release the 2nd F, HIGH and -
buttons.
3. Use the "Down cursor key" to move the indicator to SRAM INIT
(NOT the "SRAM INIT for factory TEST" ) and press ENTER.
4. Press ENTER again to confirm when prompted. A check mark will appear
in the box next to SRAM INIT on the display.
5. Use the "Down cursor key" to move the indicator to FLASH
INFORMATION CLEAR and press ENTER.
6. Press ENTER again to confirm when prompted. A check mark will appear
in the box next to FLASH INFORMATION CLEAR on the display.
7. Use the "Down cursor key" to move the indicator to EXIT and
press ENTER. This will reset the DM-24 back to the original factory
settings and the DM-24 will reboot.
보통 파이어와이어 때문에 업데이트하다가 오류가 잘 납니다.
미디 신호를 받는 과정에서 생기는 오류라고 하던데.
일단 초기화하고 리부팅해보세요.
혹시나 해보셨는지도 모르지만 메뉴얼 내용 첨부합니다.
INITIALIZATION PROCESS
1. With the power OFF hold down the 2nd F button (far left of the
board), the HIGH button (just above in the EQ section) and the -
button (just to the right in the LIBRARY section) while you turn the
power ON.
2. The DM-24 will boot to DIAGNOSTIC MODE. As soon as you see
DIAGNOSTIC MODE on the display you may release the 2nd F, HIGH and -
buttons.
3. Use the "Down cursor key" to move the indicator to SRAM INIT
(NOT the "SRAM INIT for factory TEST" ) and press ENTER.
4. Press ENTER again to confirm when prompted. A check mark will appear
in the box next to SRAM INIT on the display.
5. Use the "Down cursor key" to move the indicator to FLASH
INFORMATION CLEAR and press ENTER.
6. Press ENTER again to confirm when prompted. A check mark will appear
in the box next to FLASH INFORMATION CLEAR on the display.
7. Use the "Down cursor key" to move the indicator to EXIT and
press ENTER. This will reset the DM-24 back to the original factory
settings and the DM-24 will reboot.